While you would normally want to discount these entirely, they do have a role. They’re generally very cheap and effective enough that they’re fine to use if you only weld very rarely and don’t need comprehensive, robust protection. If you’re the kind of operator who pulls out a welding torch once a month and does a few minutes of work, a basic, cheap welding mask is all you really need. On the other hand, if you’re doing a lot more welding, a better helmet is a good idea. Masks can also be useful if you have people who do welding for you and need some kind of protection, and they forget or don’t bring their own. Having a mask as a backup helps prevent downtime and is a “better than nothing” tool to keep on hand. See even more information at Fume Extraction.
Welding is a vital process in many industries, but it involves significant hazards that can pose risks to health and safety. Understanding and implementing rigorous safety protocols is not only a responsibility, it’s an essential part of every welder’s daily routine. These measures help prevent accidents, reduce injury risks, and ensure a safer workplace for everyone involved. Welders face various dangers including burns from hot metal and sparks, eye damage from ultraviolet and infrared rays emitted during welding, respiratory issues from inhaling fumes and gases, and risks of electric shock. Each hazard requires specific precautions to protect the health and safety of welders.
The strength of a joint can be imperative or a non-factor, depending on the purpose of the welding process. Arc welding joints are generally extremely strong unless they are not performed properly. The resulting strength of the material is often at least as strong as the base materials and, in many cases, actually stronger. Brazing joints are not structural in general, but they can bear some load. In plumbing, for example, water hammering can be an issue in some systems, so the joints need to be able to stand up to that kind of force. They are not structural, however, so there is a maximum load they can bear. Soldering joints are almost never structural in any way, and the forces they handle are more electrical than tensile, linear, or shear. As such, they are not very strong, but they don’t need to be. There should, ideally, be next to no force put on them.
SMAW is a reliable welding process that offers versatility in welding different metals and various conditions. It’s also portable and lightweight, with no need for a gas tank as with some of the other welding methods mentioned previously. The welding electrode comes as a welding rod, making it perfect for tight spaces and awkward welding positions. Flux-cored arc welding (FCAW) is an automatic or semiautomatic process that uses a welding electrode that contains a flux core that acts as a shielding agent. Additional protection from contaminants is called dual-shielded FCAW, wherein a shielding gas is used along with the flux-cored electrode.
How to pick a welder tips: Fan on demand: Lowers running costs and reduces contamination to internal components. The fan kicks in when it’s needed, rather than running all day. Printed Circuit board protection: If the machine’s PCB’s are protected from dust & kept away from the fan, reliability will increase. Some manufacturers’ have the parts that need cooling in a duct type housing & the PCB isolated separately. Step voltage settings: If you’re looking at step voltage conventional MIG with multiple power settings – “the more the better!”
US tool brand DeWalt are known for making the best angle grinders, and the DCG405N is a step above the competition. Cutting the cord once and for all, this is a powerful grinder that makes use of DeWalt’s excellent XR battery system. This Dewalt angle grinder is not just a powerful cordless grinder though. The grip shape is supremely comfortable, and the whole unit weighs just 1 kg without the battery installed. You can lock-off the power switch when you need to get the grinder into awkward spots as well. This brushless angle grinder also features a host of clever safety features. I like the no-volt release to prevent accidental start-ups when a new battery is installed. The electronic brake and clutch are essential for safe operation too. The 18V brushless motor is ideal for battery use. It can make 69 cuts in ½” steel rebar when used with a 5.0 Ah battery. It doesn’t come with any batteries or one of DeWalt’s excellent TSTAK cases though, which is the case with bare power tools.
United Kingdom market dive: Metal inert gas welders—also known as MIG welders or gas metal arc welders (GMAW)—are the most commonly used welding machine, competing with the also successful TIG (tungsten inert gas or gas tungsten arc welding) and stick welders. For both at home and industrial use, metal inert gas MIG welders are known for their efficiency at fusing all kinds of metals together. Dependent on your welding skill level, whether you’re experience or looking to start welding; a metal inert gas level could be a process you’d want to try out.
Store the Cylinders Correctly: The cylinders should be stored in a dry, ventilated, and well-drained area, and away from ignitable and inflammable materials. Empty cylinders must be stored separately. OSHA also mandates the facility owners to store oxygen and fuel gas cylinders separately. The storage facilities should display proper warning signs for people regarding the dos and don’ts in the area where the cylinders are stacked. Always take care to store acetylene gas cylinders, as well as other compressed gas cylinders vertically. In addition to the above, the following should be practiced while handling the compressed gas cylinders. The cylinders feature tags, markings, or stencil marks for easy identification. Never deface or tamper these identification marks while using the cylinders.
One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.
Although this class of welders is referred to generically as MIG welders, the technical definition is “wire feed”, meaning they use a motor-driven spool to feed wire into the weld puddle. MIG means “Metal-Inert Gas” and refers to a flow of inert gas that shields the metal wire as it is consumed and melts into the puddle. If the machine isn’t able to connect and regulate a flow of inert gas like argon or carbon dioxide, it’s technically not a MIG welder. An example in this review is the Forney Easy Weld 140 FC-i, which doesn’t have gas shielding capability. This is a flux-core wire feed machine. The wire that’s used in these machines has welding flux embedded in the core. When it hits the arc, the metal melts and the flux is released as vapor, providing a shielding gas. This was originally designed as a way to deal with windy conditions defeating the gas shield of a MIG torch. It’s not as clean as true MIG welding but usually, the difference is minor, especially in a home workshop setting. However, with aluminum or stainless steel, the weld won’t be correctly joined without true gas shielding and a quiet setting. Flux core won’t be enough for these projects.
A few tips about welding equipment, MIG and TIG welders, plasma cutters. TIG welding is similar to to a MIG welder as it uses an electric arc in the same was as MIG welding does but differs in a few ways. Instead of a continuous spool of consumable wire, a TIG welder uses long tungsten welding rods that are manually slowly fed into the weld puddle to join the metal. TIG welding requires gas, usually argon, to protect and cool the weld puddle from external contamination. TIG welding is more suited to welding thinner materials such as stainless steel and aluminium as you can get the power down lower to reduce the risk of blow through and can even weld two dissimilar metals. Suitable for tricky welds such as S curves but TIG welders are still capable of welding heavier materials depending on the machine. TIG welding takes more practice that MIG welding as the process is much more manual with controlling the torch, welding rod and gas by hand (and foot for the gas) but once mastered will produce the highest quality welds making it the better choice where perfect, precise welds are required but due to the manual process is the least productive.
PACE Fume Extraction Systems provide effective odor reduction from the limited use of adhesives, solvents, and other compounds during handheld drilling, milling, or grinding operations. The filter cartridges are disposable, which makes them easier to use for fume extraction. Sturdy Steel Case and Lightweight Build Quality The Arm-Evac 150 comes with a steel case, which I found to be quite sturdy. It also has a dependable brushless motor that doesn’t need expensive routine maintenance. The overall unit is built with 20-gauge steel, which is ESD-safe. This tiny, low-profile machine will fit anywhere you need, and it comes with lockable casters for convenient mobility and transportation. The compact unit weighs only 20 pounds which makes it extremely lightweight.
This drill has a powerful 9 Amp motor, high-end 2-coil magnet, and compatible with ¾” diameter shank annular cutters. To start off, this drill is very proud of how easy it is to handle. It weighs a mere 26.5 pounds and it has a conveniently located handle, making uncomfortable drilling positions more bearable. It has a straightforward 2-button control panel that is also conveniently located and easy to use. Other perks that you get with this drill is a hard case and, depending on where you buy, you may also receive a kit containing German-made annular cutters. Like some of the other drills in this list, you can also fit the feeding handles on either side of the drill, depending on what is ergonomic and comfortable for you. This drill also has an easy to turn off feature to add an element of safety to your drilling. This button is big and easily accessible. This is a solid drill that is perfect for all handymen.
ESAB is a world leader in the production of welding and cutting equipment and consumables. Our innovative, world-renowned equipment and solutions are developed with input from our customers and built with the expertise and heritage of a global manufacturing leader. For each discipline, continuous development of methods, materials and know-how is being directed to meet the challenges posed by the diversity of industry sectors we serve. ESAB is organized to deliver efficient, high-productivity solutions to meet customer requirements in a manner that exceeds their expectations no matter the market segment. Continuous Improvement (Kaizen) Is Our Way Of Life – Set breakthrough objectives, experiment and learn every day, eliminate waste in our business processes, and benchmark the best, then better them. Living this value is done through understating that Change is a Must, and the use of Tools for Improvement. To live this value each ESAB associate fosters an environment of continuous learning employing the Colfax Business System Tools which is the basis of our culture.
Welding Supplies Direct are the UK distributor for GPPH welding tables, manufactured to the highest standards in Europe. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. Our modular welding benches come equipped with a hole system of all sides (tabletop & all sides); the holes are 28MM in diameter and have a chamfered edge for easy tool assembly. You have the option of standard legs or castors being fitted, too.
Another quality machine from Hobart that has 25A for 190A output range so you can weld up to 5/16 in steel. The power input is only 230V so you won’t be able to use this on your standard household power outlet. The 190 is a wise choice if you’re considering buying a 140A welder but think you may want to upgrade in the future. It’s not much more expensive and you can always turn the 190 down but you can’t turn a 140 up. There’s loads including for the price, you get power, durability, a good duty cycle and all the extras you need to get started, including .030 contact tips, 0.30 flux cored wire and gas gauges. See the full review here.
It’s also worth looking into how your welder will handle things like short-circuiting. If a short circuit issue occurs while you’re welding, you don’t want a surge of power to ruin your work. Fortunately, there are many welding companies that implement strategies in their devices to eliminate the risks of short circuits. To choose the correct portability, size and weight for your welder, you’ll need to think about what you’ll need the machine for. If you’re going to be carrying it around a lot, then you need something that’s going to be highly portable and lightweight. Just make sure that a reduction in weight doesn’t mean that you end up compromising on power or performance. Read extra info on https://www.weldingsuppliesdirect.co.uk/.
Sealey is one of the biggest manufacturers of tools and accessories in the UK, offering approximately 8000 items including tools for home, repair shops, agricultural facilities, as well as cleaning. In this variety, we found a gasless MIG welder MIGHTYMIG 100. The machine is able to weld metal sheets of a different thickness thanks to a toggle that allows setting the amperage to the minimum and maximum. The output range will be 55? and 100?, respectively. We should say that the welding time at the minimum power won’t be over 6 minutes. Yet, this welder will run for about 2 minutes at 90? and that’s great considering its moderate price. In addition, you’ll be able to manage the joint by varying the speed of the wire feed, just turn the relevant control knob to the desired setting. By the way, the welder is compatible with a flux-cored wire up to 0.9 mm, and the weight of the spool should be 0.9 kg. Like most welding tools, it features an overheating protection, and the orange light will notify you when the welder gets overheated after a long use. Apart from that, the forced air cooling system will chill the welder’s internal parts. The welder has a non-live torch for your convenience that will increase the accuracy of welding and provide safety.
Fume extraction supplies shopping UK right now
July 8, 2024
Industrial
Comments Off on Fume extraction supplies shopping UK right now
Terence Clear
While you would normally want to discount these entirely, they do have a role. They’re generally very cheap and effective enough that they’re fine to use if you only weld very rarely and don’t need comprehensive, robust protection. If you’re the kind of operator who pulls out a welding torch once a month and does a few minutes of work, a basic, cheap welding mask is all you really need. On the other hand, if you’re doing a lot more welding, a better helmet is a good idea. Masks can also be useful if you have people who do welding for you and need some kind of protection, and they forget or don’t bring their own. Having a mask as a backup helps prevent downtime and is a “better than nothing” tool to keep on hand. See even more information at Fume Extraction.
Welding is a vital process in many industries, but it involves significant hazards that can pose risks to health and safety. Understanding and implementing rigorous safety protocols is not only a responsibility, it’s an essential part of every welder’s daily routine. These measures help prevent accidents, reduce injury risks, and ensure a safer workplace for everyone involved. Welders face various dangers including burns from hot metal and sparks, eye damage from ultraviolet and infrared rays emitted during welding, respiratory issues from inhaling fumes and gases, and risks of electric shock. Each hazard requires specific precautions to protect the health and safety of welders.
The strength of a joint can be imperative or a non-factor, depending on the purpose of the welding process. Arc welding joints are generally extremely strong unless they are not performed properly. The resulting strength of the material is often at least as strong as the base materials and, in many cases, actually stronger. Brazing joints are not structural in general, but they can bear some load. In plumbing, for example, water hammering can be an issue in some systems, so the joints need to be able to stand up to that kind of force. They are not structural, however, so there is a maximum load they can bear. Soldering joints are almost never structural in any way, and the forces they handle are more electrical than tensile, linear, or shear. As such, they are not very strong, but they don’t need to be. There should, ideally, be next to no force put on them.
SMAW is a reliable welding process that offers versatility in welding different metals and various conditions. It’s also portable and lightweight, with no need for a gas tank as with some of the other welding methods mentioned previously. The welding electrode comes as a welding rod, making it perfect for tight spaces and awkward welding positions. Flux-cored arc welding (FCAW) is an automatic or semiautomatic process that uses a welding electrode that contains a flux core that acts as a shielding agent. Additional protection from contaminants is called dual-shielded FCAW, wherein a shielding gas is used along with the flux-cored electrode.
How to pick a welder tips: Fan on demand: Lowers running costs and reduces contamination to internal components. The fan kicks in when it’s needed, rather than running all day. Printed Circuit board protection: If the machine’s PCB’s are protected from dust & kept away from the fan, reliability will increase. Some manufacturers’ have the parts that need cooling in a duct type housing & the PCB isolated separately. Step voltage settings: If you’re looking at step voltage conventional MIG with multiple power settings – “the more the better!”
US tool brand DeWalt are known for making the best angle grinders, and the DCG405N is a step above the competition. Cutting the cord once and for all, this is a powerful grinder that makes use of DeWalt’s excellent XR battery system. This Dewalt angle grinder is not just a powerful cordless grinder though. The grip shape is supremely comfortable, and the whole unit weighs just 1 kg without the battery installed. You can lock-off the power switch when you need to get the grinder into awkward spots as well. This brushless angle grinder also features a host of clever safety features. I like the no-volt release to prevent accidental start-ups when a new battery is installed. The electronic brake and clutch are essential for safe operation too. The 18V brushless motor is ideal for battery use. It can make 69 cuts in ½” steel rebar when used with a 5.0 Ah battery. It doesn’t come with any batteries or one of DeWalt’s excellent TSTAK cases though, which is the case with bare power tools.
United Kingdom market dive: Metal inert gas welders—also known as MIG welders or gas metal arc welders (GMAW)—are the most commonly used welding machine, competing with the also successful TIG (tungsten inert gas or gas tungsten arc welding) and stick welders. For both at home and industrial use, metal inert gas MIG welders are known for their efficiency at fusing all kinds of metals together. Dependent on your welding skill level, whether you’re experience or looking to start welding; a metal inert gas level could be a process you’d want to try out.
Store the Cylinders Correctly: The cylinders should be stored in a dry, ventilated, and well-drained area, and away from ignitable and inflammable materials. Empty cylinders must be stored separately. OSHA also mandates the facility owners to store oxygen and fuel gas cylinders separately. The storage facilities should display proper warning signs for people regarding the dos and don’ts in the area where the cylinders are stacked. Always take care to store acetylene gas cylinders, as well as other compressed gas cylinders vertically. In addition to the above, the following should be practiced while handling the compressed gas cylinders. The cylinders feature tags, markings, or stencil marks for easy identification. Never deface or tamper these identification marks while using the cylinders.
One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.
Although this class of welders is referred to generically as MIG welders, the technical definition is “wire feed”, meaning they use a motor-driven spool to feed wire into the weld puddle. MIG means “Metal-Inert Gas” and refers to a flow of inert gas that shields the metal wire as it is consumed and melts into the puddle. If the machine isn’t able to connect and regulate a flow of inert gas like argon or carbon dioxide, it’s technically not a MIG welder. An example in this review is the Forney Easy Weld 140 FC-i, which doesn’t have gas shielding capability. This is a flux-core wire feed machine. The wire that’s used in these machines has welding flux embedded in the core. When it hits the arc, the metal melts and the flux is released as vapor, providing a shielding gas. This was originally designed as a way to deal with windy conditions defeating the gas shield of a MIG torch. It’s not as clean as true MIG welding but usually, the difference is minor, especially in a home workshop setting. However, with aluminum or stainless steel, the weld won’t be correctly joined without true gas shielding and a quiet setting. Flux core won’t be enough for these projects.
A few tips about welding equipment, MIG and TIG welders, plasma cutters. TIG welding is similar to to a MIG welder as it uses an electric arc in the same was as MIG welding does but differs in a few ways. Instead of a continuous spool of consumable wire, a TIG welder uses long tungsten welding rods that are manually slowly fed into the weld puddle to join the metal. TIG welding requires gas, usually argon, to protect and cool the weld puddle from external contamination. TIG welding is more suited to welding thinner materials such as stainless steel and aluminium as you can get the power down lower to reduce the risk of blow through and can even weld two dissimilar metals. Suitable for tricky welds such as S curves but TIG welders are still capable of welding heavier materials depending on the machine. TIG welding takes more practice that MIG welding as the process is much more manual with controlling the torch, welding rod and gas by hand (and foot for the gas) but once mastered will produce the highest quality welds making it the better choice where perfect, precise welds are required but due to the manual process is the least productive.
PACE Fume Extraction Systems provide effective odor reduction from the limited use of adhesives, solvents, and other compounds during handheld drilling, milling, or grinding operations. The filter cartridges are disposable, which makes them easier to use for fume extraction. Sturdy Steel Case and Lightweight Build Quality The Arm-Evac 150 comes with a steel case, which I found to be quite sturdy. It also has a dependable brushless motor that doesn’t need expensive routine maintenance. The overall unit is built with 20-gauge steel, which is ESD-safe. This tiny, low-profile machine will fit anywhere you need, and it comes with lockable casters for convenient mobility and transportation. The compact unit weighs only 20 pounds which makes it extremely lightweight.
This drill has a powerful 9 Amp motor, high-end 2-coil magnet, and compatible with ¾” diameter shank annular cutters. To start off, this drill is very proud of how easy it is to handle. It weighs a mere 26.5 pounds and it has a conveniently located handle, making uncomfortable drilling positions more bearable. It has a straightforward 2-button control panel that is also conveniently located and easy to use. Other perks that you get with this drill is a hard case and, depending on where you buy, you may also receive a kit containing German-made annular cutters. Like some of the other drills in this list, you can also fit the feeding handles on either side of the drill, depending on what is ergonomic and comfortable for you. This drill also has an easy to turn off feature to add an element of safety to your drilling. This button is big and easily accessible. This is a solid drill that is perfect for all handymen.
ESAB is a world leader in the production of welding and cutting equipment and consumables. Our innovative, world-renowned equipment and solutions are developed with input from our customers and built with the expertise and heritage of a global manufacturing leader. For each discipline, continuous development of methods, materials and know-how is being directed to meet the challenges posed by the diversity of industry sectors we serve. ESAB is organized to deliver efficient, high-productivity solutions to meet customer requirements in a manner that exceeds their expectations no matter the market segment. Continuous Improvement (Kaizen) Is Our Way Of Life – Set breakthrough objectives, experiment and learn every day, eliminate waste in our business processes, and benchmark the best, then better them. Living this value is done through understating that Change is a Must, and the use of Tools for Improvement. To live this value each ESAB associate fosters an environment of continuous learning employing the Colfax Business System Tools which is the basis of our culture.
Welding Supplies Direct are the UK distributor for GPPH welding tables, manufactured to the highest standards in Europe. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. Our modular welding benches come equipped with a hole system of all sides (tabletop & all sides); the holes are 28MM in diameter and have a chamfered edge for easy tool assembly. You have the option of standard legs or castors being fitted, too.
Another quality machine from Hobart that has 25A for 190A output range so you can weld up to 5/16 in steel. The power input is only 230V so you won’t be able to use this on your standard household power outlet. The 190 is a wise choice if you’re considering buying a 140A welder but think you may want to upgrade in the future. It’s not much more expensive and you can always turn the 190 down but you can’t turn a 140 up. There’s loads including for the price, you get power, durability, a good duty cycle and all the extras you need to get started, including .030 contact tips, 0.30 flux cored wire and gas gauges. See the full review here.
It’s also worth looking into how your welder will handle things like short-circuiting. If a short circuit issue occurs while you’re welding, you don’t want a surge of power to ruin your work. Fortunately, there are many welding companies that implement strategies in their devices to eliminate the risks of short circuits. To choose the correct portability, size and weight for your welder, you’ll need to think about what you’ll need the machine for. If you’re going to be carrying it around a lot, then you need something that’s going to be highly portable and lightweight. Just make sure that a reduction in weight doesn’t mean that you end up compromising on power or performance. Read extra info on https://www.weldingsuppliesdirect.co.uk/.
Sealey is one of the biggest manufacturers of tools and accessories in the UK, offering approximately 8000 items including tools for home, repair shops, agricultural facilities, as well as cleaning. In this variety, we found a gasless MIG welder MIGHTYMIG 100. The machine is able to weld metal sheets of a different thickness thanks to a toggle that allows setting the amperage to the minimum and maximum. The output range will be 55? and 100?, respectively. We should say that the welding time at the minimum power won’t be over 6 minutes. Yet, this welder will run for about 2 minutes at 90? and that’s great considering its moderate price. In addition, you’ll be able to manage the joint by varying the speed of the wire feed, just turn the relevant control knob to the desired setting. By the way, the welder is compatible with a flux-cored wire up to 0.9 mm, and the weight of the spool should be 0.9 kg. Like most welding tools, it features an overheating protection, and the orange light will notify you when the welder gets overheated after a long use. Apart from that, the forced air cooling system will chill the welder’s internal parts. The welder has a non-live torch for your convenience that will increase the accuracy of welding and provide safety.